Loading...

Skip to main content

History: Glossary of Woodworking Hand Tools

View published page Edit published page Collapse Into Edit Sessions

Source of version: 13

«
»

!A
---
__[https://thepatriotwoodwiki.org/Adze|Adze]__ - An adze is similar to an axe, imagine an axe with its blade at a right angle to its haft (helve or handle). 

__[https://thepatriotwoodwiki.org/Adze#Carpenter_s|Adze, Carpenters]__ - This adze similar to the standard adze, yet has a square back of the blade, that can be used for striking other object as in a hammer or maul action.

__[https://thepatriotwoodwiki.org/Adze#Cooper_s|Adze, Coopers]__ - The coopers adze is held by one hand and has a curved blade, typically used by barrel makers, favored for its small and easy to use weight and size, and for the curved blade.

__[https://thepatriotwoodwiki.org/Adze#Sculptor|Adze, Sculptors]__ - The sculptors adze has a straighter blade quite the opposite of the coopers adze, it as well is used by one hand.

__[https://thepatriotwoodwiki.org/Adze#Ship_carpenter_s|Adze, Ship Carpenters]__ - This specialty adze has a blade similar to the shape of a garden hoe, and is fitted with a spur on the back of the blade, the spur is used to set large nails or to punch holes or indentations into the wood.

!B
---

!C
---

!D
---

!E
---

!F
---

!G
---
__Gauge marking__ - made of wood or steel. The one most commonly used consists of a square, wooden bar or beam, about 8 in. long, on which a wooden block or head slides. This block can be fastened at any point of the bar by means of a brass set-screw bearing against a brass shoe. The block, on the best grade of gauge, is protected from wear by a piece of brass set flush with its surface. The bar is graduated in inches and provided with a steel point or spur fastened near the end with a screw. The spur must be filed to a fine point. 
This tool is used for marking or gauging widths on narrow pieces of wood, such as table legs, etc. When using it. move the gauge away from you, and tip is slightly forward, keeping the block in contact with the edge or face of the board at all times.

__Gauge slitting__ - is similar to the panel gauge, but has a handle in addition to the block. It has a knife instead of a spur and is used for cutting thin stock.

__Gauge mortising__ - is a marking gauge with two spurs, which can be spaced at different distances and mark two parallel lines at the same time. One type is made of rosewood and has and adjusting screw in the end of the beam, which moves one of the points up or down the as desired. The other side of the beam is fitted with a single point as an ordinary marking gauge. This gauge is used chiefly for layout out mortises and tenons. Other types are made entirely of metal and have two bars.

!H
---

!I
---

!J
---

!K
---

!L
---

!M
---
__Measuring tape__ - Used by carpenters, contractors, and architects. They are made of steel or cloth, and usually measure from 25 to 100 ft. in length. They are divided into inches and feet, or meters and centimeters.{FOOTNOTE(tag="herman")}Hjorth, Herman, 1883-1951. Principles of Woodworking. Milwaukee, Wis.: The Bruce publishing company, 1930. {FOOTNOTE}

__Miter and try-square__ - can be used at both 90 and 45 degrees. Miter squares can only be used for angles of 45 degrees.{footnote sameas="herman"}

!N
---

!O
---

!P
---

!Q
---

!R
---
__Rule__ - Rules are made in different lengths and of different materials. Those used by woodworkers are usually of the folding type, and measure from 2 to 8 feet in length. Rules are generally marked off on both sides in inches and subdivisions of an inch, but they are also made with such divisions on one side and metric divisions on the other.{footnote sameas="herman"}

!S
---
__Sliding T bevel__ - are similar to try-squares, but differ in that their blades are adjustable to any angle. They are used for laying out angles other than right angles, as for instance, corners braces, dovetails, or side rails for chairs.{footnote sameas="herman"} 

!T
---
__Try-square__ - Used for testing the squareness of lumber, and in checking the squareness of work being assembled, especially in places where a framing square would be too large. Try-squares consist of two parts, the stock and the blade, which are firmly fastened together at right angles. The stock is thick and made of wood or iron. The blade, which is thin, is made of steel and has an inch scale stamped on it. Try-squares are made in sizes from 4 to 12 in., measured from the end of the blade to the stock.{footnote sameas="herman"}

!U
---

!V
---

!W
---

!X
---

!Y
---

!Z
---
!Reference
{footnotearea }
{showreference showtitle="yes" hlevel="1"}

History

Enable pagination rows per page

Advanced

Information	Version
07-06-2024 18:12 admin img Plugin modified by editor.	254
07-06-2024 18:11 admin	253
07-06-2024 18:10 admin	252
07-06-2024 18:09 admin mouseover Plugin modified by editor.	251
07-06-2024 18:09 admin mouseover Plugin modified by editor.	250
07-06-2024 18:07 admin	249
07-06-2024 18:03 admin	248
07-06-2024 18:01 admin	247
07-06-2024 17:57 admin	246
01-06-2023 09:32 anonymous	245
01-06-2023 09:31 anonymous	244
01-06-2023 09:30 anonymous img Plugin modified by editor.	243
11-13-2022 05:53 admin files Plugin modified by editor.	242
11-13-2022 05:53 admin files Plugin modified by editor.	241
11-13-2022 05:50 admin files Plugin modified by editor.	240
11-13-2022 05:49 admin files Plugin modified by editor.	239
11-13-2022 05:49 admin img Plugin modified by editor.	238
11-13-2022 05:47 admin files Plugin modified by editor.	237
11-13-2022 05:46 admin img Plugin modified by editor.	236
11-13-2022 05:45 admin img Plugin modified by editor.	235
11-13-2022 05:45 admin added caliper image	234
11-13-2022 05:39 admin added mousever to pein hammer	233
11-13-2022 05:37 admin added mousever to claw hammer	232
11-13-2022 05:33 admin added caliper descriptions	231
11-12-2022 09:59 admin deleted text	230

«
1 (current)
2
3
…
11
»